CompuSTAR 1W900SHR-961 Installationshandbuch

Installation Manual By Firstech LLC, Version: 1.0 Applicable to the following control modules: - CM4200-DX (remote start) - CM5200 (DT remote start w

10 STEP 3: Exit the vehicle and close the door. The vehicle’s engine should shut off upon closing the door. If the vehicle’s engine does not shut o

11

12CM5200 Wiring Schematic (Remote Start) The CM5200 is the control module for all remote start units. This controller is universal regardless of remo

13CM4200-DX Wiring Schematic (Remote Start) The CM4200-DX is the control module for all remote start units. This controller is universal regardless

14CM5000 Wiring Schematic (Alarm and Remote Start) The CM5000 is the control module for all alarm and remote start combo units. This controller is un

15CM4000 Wiring Schematic (Alarm and Remote Start) The CM4000 is the control module for all alarm and remote start combo units. This controller is u

16CM5200, CM4200-DX, CM5000 and CM4000 Wiring Description Connector 1 (CN1), 8-Pin Pin 1 Red - Constant 12V positive (+) power input. This wire

17There are two wires coming off of the relay; yellow-black and yellow. To utilize the anti-grind or starter-kill features, the vehicles starter wire

18Pin 3 Red/Black [POC 2] – 2nd Starter 250mA negative (-) output. This output can be used to trigger the pre-wired relay located on the main ignit

19Pin 14 Yellow/Black - Engine sensing input. This wire is connected to the vehicles Tach or Alternator wire and is required if you are not using th

2Table of Contents Introduction...

20 Pin 1 Black - L.E.D negative (-) ground. Pin 2 Black/White- L.E.D. 3V positive (+) output. Connector 6 (CN6), 4-Pin (Pre-wired Shock Senso

21 Pin 1 Gray/Black - Negative (-) ground. Pin 2 Gray – 3V positive (+) L.E.D. output. Pin 3 Gray – Negative (-) output. Connector 10 (CN10)

22CM4300 Wiring Schematic (Alarm) The CM4300 is the control module for all alarm units. This controller is universal regardless of remote or antenna

23CM4300 Wiring Description Connector 1 (CN1), 4-Pin Pin 1 Red - Constant 12V positive (+) power input. This wire must be connected. The proper

24Pin 1 Green/White [POC 1] - Parking light 250mA negative (-) output. The proper wire will test (-) when the parking light switch is in the on posi

25 Pin 11 Violet/Black - 250mA negative (-) output when armed. This wire is pre-wired to the starter-kill relay. Caution: When this wire is bein

26 OPTION GROUP 1 Feature Default Setting - I Optional Setting - II Optional Setting - III Optional Setting - IV 1-

27 OPTION GROUP 4 Feature Default Setting - I Optional Setting - II Optional Setting - III Optional Setting - IV 4-01 Aux 1 output 0.

28Option Menu Descriptions Only uncommon options are described in this section. 1-03 Driver’s Priority Unlock - The driver’s door must be isolated

29Option 4: Will start once every 24 hours if the temperature falls below Option settings 2-08 or above Option settings 2-09. For example, if you wa

3Introduction Thank you for purchasing this Firstech system for your vehicle. The following installation manual is intended for experienced and auth

303-10 Valet – This option changes valet modes. Default 1: Key on/off five times or remote valet (I + III for 0.5 seconds) with key in the on posit

31 4-11 Bypass Brand Through RS232 Port – Default setting allows for compatibility with ADS Idatalink modules. Setting 2 changes compatib

32 Following the auxiliary and diesel settings (if selected), the POC options will be displayed on the OP500. The POCs can be set between 0 (default

33STEP 3: Once finished scrolling through the menu wait for the parking lights and/or siren chirp to confirm the option number. i.e. option 2-04 will

34 I have these control modules that say MM720 and MM721. What are they? A: These control modules are the new CM5 series. MM720 = CM5000 and MM721 =

35The vehicle starts and shuts down 3 times in a row. A: This usually means that the engine sensing mode is not working correctly. If you are using

36Technical Support Contacts Firstech technical support is reserved for authorized dealers only. Monday - Friday 888-820-3690 (7:00 am – 5:

4Installation Basics If you are new to installing Firstech Series Remote Starts and / or Alarms, we highly recommended that you thoroughly review th

5Remote Programming Routine IMPORTANT: Any and all remotes must be coded to the control module prior to performing any and all operations. Remotes e

6Placement and Use of Components IMPORTANT: The placement and use of components are critical to the performance of this system. Antenna and Cable Fi

7significant difference in sensitivity for both 1st and 2nd stages. Recommended dial settings for most vehicles is somewhere between 2 & 4. Siren

8You Must Have the OP500 Option Programmer To set auxiliary outputs on the control module involves the new Programmable Output Connector wires (POCs)

9 STEP 1: Change Option 2-10 to setting 3 - No tach sensing. STEP 2: Process complete – there is no further programming required other than adjust