CompuSTAR CM6300 Installationsanleitung

Version 6.07

Placement and Use of Components CM6300CM6300 Install GuideAlarm Systemwww.firstechonline.com | www.compustar.c

CM6300 Install GuideAlarm Systemwww.firstechonline.com | www.compustar.comThermister (Temperature Sensor)Every 2 Way LCD Firstech RF kit includes an o

The CM6 Series Blade connector has a locking tab. Older blade harnesses will work but you must cut the notches on the black harness plug off.Blade sys

Connector 1 (CN1), 4-PinPin 1 Red - Constant 12V positive (+) power input. This wire must be connected. The proper vehicle wire will test (+) 12

Connector 4 (CN4), 20-Pin: Programmable Output Connector (POC)IMPORTANT: Odd Pin numbers 1 through 17 are programmable for up to 19 different output

Pin 11 Black [POC 5] – Auxiliary 2 250mA negative (-) output. This is an optional output that will provide a programmable output to trigger slidin

Connector 5 (CN5), 6-PinPin 1 Not usedPin 2 Violet/White - Trunk release 250mA negative (-) output. This is an optional output that will release

Connector 7 (CN7), 4-Pin to 4-Pin or 6-Pin (Pre-wired Antenna Cable)Connect your antenna cable to this port. You can only use 4 to 4 pin or 4 to 6 pin

Connector 11 (CN11), 2-Pin (Pre-wired LED)Note: Do not mistake for Thermister port.Pin 1 Black - L.E.D negative (-) ground. Pin 2 Black/White- L.E

Option Programming Tables CM6300Option Group 1Feature Default Setting - IOptional Setting - IIOpt

CM6300 Install GuideAlarm Systemwww.firstechonline.com | www.compustar.com Table of Contents

Option Group 4Feature Default Setting - IOptional Setting - IIOptional Setting - IIIOptional Setting - IV4-01Aux 1 output 0.5sec Latch0.5 sec Pulse +

Special Option Group 1Feature Setting Value (Seconds)2 AUX1 output time 1 ~ 1003 AUX2 output time 1 ~ 1004 AUX3 output time 1 ~ 1005 AUX4 output time

1-04 Double Pulse Unlock - If enabled, this option will cause the system to double pulse the lock, unlock or both lock and unlock outputs. This

3-04 Starter-Kill – This option determines the mode of the anti-grind/starter-kill relay. Default 1: Anti-grind + starter-kill Option 2: Anti-gri

3-15 Soft Disarm - When a vehicle has a factory alarm, and the Firstech alarm is triggered, you may have both alarms triggered at the same time.

4-07 Aux 2 Input – This option changes the input behavior of the instant trigger wire on the Aux Input Sensor green connector. Default 1:. Will

Special Option Groups 1 & 2 CM6300IMPORTANT: The OP500 is required to change settings in Speci

CM6300 Install GuideAlarm Systemwww.firstechonline.com | www.compustar.comAt the end of menu 4, if diesel mode or auxiliary setting functions were ena

How To Program Options With 1 Way Remotes With 2 Way Remotes (Wait for chirp between each tap)Scroll Through Menu (Wait for chirp between each tap)Wai

CM6300 Install GuideAlarm Systemwww.firstechonline.com | www.compustar.com Troubleshooting

CM6300 Install GuideAlarm Systemwww.firstechonline.com | www.compustar.comCopyright 2011 Firstech, LLC.Page 3

Whenever I try to arm the vehicle, it chirps the siren 3 times and will not arm.A: Check the hood and trunk trigger inputs.Do the door locks flip flop

CM6300 Install GuideAlarm Systemwww.firstechonline.com | www.compustar.comFirstech technical support is reserved for authorized dealers only.Monday -

Introduction CM6300Thank you for purchasing this Firstech system for your

Installation Basics CM6300If you are new to installing Firstech Series Remote Start

Remote Programming Routine CM6300IMPORTANT: Any and all remotes must be coded to the control module pr

Placement and Use of Components CM6300RPS Touch and RPS (Remote Paging Sensor)The RPS is an optional feature.

2 Way LCD remote pagingTo page a 2 Way LCD remote just tap the ‘Red Circle’ twice.Touch Panel SensitivityTo change touch sensitivity open the driver’s

STEP 5: The LED on the RPS will confirm your first number by flashing BLUE slowly. Once the LED begins to flash rapidly in BLUE, enter your second num