CompuSTAR 1WAMR-Fiance Bedienungsanleitung PDF herunterladen (Seite 14)

27 By Firstech, LLC By Firstech, LLC 26

Advanced System Functions

t@t@m

This feature can not be turned on with the 2 Way remote. The built in turbo timer keeps the vehicle’s engine running for either 1, 2, or 4 minutes

(programmable from dealer with Option 2-2) after the vehicle key has been removed from the ignition. This feature will keep oil running through the

turbo system to allow for appropriate cooling time. Tap the Trunk and Key buttons simultaneously for 0.5 seconds to turn on or off turbo mode. The

remote will beep once and the turbo icon will illuminate to confirm that turbo mode is activated. The remote will beep twice and icon will disappear to

confirm turbo mode is off.

IMPORTANT: To utilize this feature, the emergency / parking brake wire must be connected to the NuStart system. Consult your local authorized

NuStart dealer for installation.

c@c@O@rps@Hr@p@sI

The RPS is an optional feature. The car call/RPS feature uses a remote paging sensor that is designed to be mounted on the inside of the windshield.

After the RPS has been triggered, the car call icon will illuminate and the remote will ring several times if the remote is in range to receive commands.

To trigger the car call or RPS sensor, you must knock on the windshield in front of the RPS at least two times. The switch on the RPS will adjust paging

sensitivity - the smaller the dot represents the least sensitive setting. Use a key or pen for best results. If you do not want the remote to receive pages

from the RPS, follow the below steps to turn the feature off;

STEP1 : Enter remote programming mode by holding down buttons (II + III) simultaneously for 2.5 seconds. The remote will beep once and the LCD

will read “Prog” to indicate that you have successfully entered programming mode.

STEP2 : Once in programming mode, you can turn the feature off by tapping button (III) for 0.5 seconds. The RPS icon will

disappear. Repeat this step to turn the car call feature back on.

STEP3 : Once the car call icon is flashing, you can turn the feature off by tapping button (I) for 0.5 seconds. Repeat this step to turn

the car call feature back on.

Advanced System Functions

rps@Hr@p@sI@u@O@d

(Optional with the NU3500R) Basic RPS and car call functions do not require programming, however in order for the sensor to unlock/disarm the

vehicle you must perform the following procedures;

STEP 1: Disarm/unlock the alarm (remote must be programmed first)

STEP 2: Turn ignition key to the on position and the leave the driver s door open.

STEP 3: Knock on the windshield in front of the RPS a total of 10 times (each time you knock the LED on the RPS will flash RED). The LED will begin

to flash rapidly in BLUE with successful completion of this step.

STEP 4: Enter the first digit of the desired four-digit pass code by knocking on the windshield in front of the RPS the desired number of times. For

example, to enter 3, knock on the sensor 3 times (each time you knock the LED will flash RED) then wait.

STEP 5: The LED on the RPS will confirm your first number by flashing BLUE slowly. Once the LED begins to flash rapidly in BLUE, enter your

second number by repeating step 4.

STEP 6: Repeat steps 4 & 5 to enter all four numbers.

STEP 7: Turn the ignition OFF - the RPS disarm/unlock feature is now programmed. Follow steps 3 - 5 to enter your disarm/unlock code.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

CompuSTAR 1WAMR-Fiance Bedienungsanleitung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernbedienungen CompuSTAR 1WAMR-Fiance