CompuSTAR CM4200DX Installationsanleitung PDF herunterladen (Seite 18)

This option setting will set the unlocking/disarming of the control module during the trunk release through the

remote. Setting 2 keeps the doors locked, disarms the alarm and opens trunk. Setting 3 opens the trunk only.

1-8 Locking while in Passive Arming

This option determines the behavior of the locks during passive arming. After 30 seconds the vehicle will either

lock and arm or not lock and just arm.

1-9 Ignition controlled door locks: Tach sensing mode must be used for this feature to work. You must also turn this

feature on through the remote.

1-10 Auto Relock

If this option is turned on, the system will automatically relock/rearm if the system is disarmed but a door is not

opened. The auto relocking can be set for 30 seconds, 60 seconds, or 5 minutes. For setting 2, the siren will chirp

and parking lights flash every 10 seconds. For setting 3, the siren will chirp and parking lights flash every 20

seconds. For setting 4, the siren will chirp and parking lights flash every 1 minute, 40 seconds. In every instance, on

the third chirp/parking light flash the system will lock/arm.

1-11 Ignition/Accessory Out Upon Unlock

Mostly new dodge vehicles need ign/acc pulse to disarm factory alarm.

2-1 Minimum Crank Time

This option can be used to change the crank times during remote start. Please see the table for more details.

2-2 Turbo mode

This option determines how long the turbo timer runs for to allow the vehicle’s turbo to cool down. The time can be

set to 1, 2 or 4 minutes. The e-brake must be connected to the control module. You must also turn this feature on

through the remote.

2-3 Diesel Timer

The diesel timer allows you to set a wait to start time to allow the vehicle’s glow plugs to warm up. Without setting

this option you must find the vehicle’s wait to start wire. The default time for Setting 2 is 10 seconds. This can be

increased or decreased only with the Option Programmer OP500.

2-4 Trigger start: This option allows the control module to be used as a slave unit. This option determines whether the

slave start wire on CN3 requires a single or double pulse to activate remote start. This can be used on vehicles

where the user would like to keep the factory remote.

2-5 Cold Start with Thermistor Assembly: Turning this option on will turn on the cold/hot start feature. This option

works in conjunction with option 2-6. You must also set the temperatures in options 2-8 and 2-9.

2-6 Timer Start, or, Minimum Interval Between Cold Starts: This option dictates the time interval when the control

module will either remote start or check the temperature and remote start.

Option 1: Will start every 3 hours until the vehicle is remote started or started by key – 4 minute run time.

Option 2: Will start every 1.5 hours until the vehicle is remote started or started by key – 4 minute run time.

Option 3: Will start at the time specified on the 2-Way remote one time for the run time set by Option 2-7.

Option 4: Will start at the specified time on the remote every 24 hours if the temperature falls below as set under 2-

8. For example, if you want your car to start everyday at 7 AM, run for 25 minutes when the temperature of the

inside of the vehicle falls below 32°F, you need to program the following:

1) Option 2-5 (Cold Start) on setting 2

2) Option 2-6 (24 hr. repeat) on setting 4

3) Option 2-7 (25 min run-time) on setting 2

1 2 ... 13 14 15 16 17 18 19 20 21 22

Keine Kommentare

CompuSTAR CM4200DX Installationsanleitung Seite 18