CompuSTAR CM4200DX Installationsanleitung PDF herunterladen (Seite 20)

3-4 Anti-Grind/Starter-Kill relay

With this option on the default setting, the starter-kill relay will act as an anti-grind circuit only. It will not disable

the starter when the system is locked/armed. On setting 2, the starter-kill relay will act as an anti-grind and starter-

kill circuit. Setting 3 is the same as 2, but a passive starter-kill is activated 45 seconds after the vehicle is turned off

or disarmed.

3-6 Factory Alarm Option

With this option turned on, the 4200DX starter only system will function as a factory style alarm by monitoring the

door trigger and sounding the horn and flashing the parking lights if the door is opened after the doors have been

locked. The system will also page the Two-Way remotes.

3-8 Horn Output

The default setting will honk the horn when tapping the lock button twice. This is only available on 1-way remotes.

Optional setting 2 will pulse the horn on lock and unlock. Optional setting 3 will pulse the horn on lock, unlock and

remote start. Optional setting 4 will pulse the horn on double lock and remote start. This will only work on 1-way

remotes.

3-10 Valet

This option changes the way you put the system into valet mode. On default setting you can either cycle the ignition

5 times with the key or turn the ignition on and tap buttons 1+3 or lock+trunk – this is a new feature in 4000 series.

Setting 2 allows you to cycle the ignition 5 times with the key or tap buttons 1+3 or lock+trunk to put the system

into valet mode. – same as CM3000 series.

Setting 3 is a secure valet: The default code is 3, 3 or any number you entered for the RPS unlock code. See page 8

of this manual or the remote user’s guide. You can change the numbers by repeating the following steps and the

first 2 numbers of RPS unlock and secure valet codes overwrite each other.

3-11 Channel Expander Mode

This option requires installation of the Channel Expander module. If you need more than the 2 supplied auxiliary

outputs, you can install the Channel Expander for 5 additional outputs. With this option turned on, POC 9 must be

set to (10) Aux 1 and becomes the data wire that communicates with the Channel Expander. Please see the Channel

Expander instruction manual for more details.

3-12 Passive Arming with Channel Expander Mode

The ability to activate/deactivate Passive Arming through the remote is lost once Channel Expander mode is

activated. If the Channel Expander is being used, set this option to Setting 2 to activate Passive Arming with

Channel Expander Mode. Leave it on the default setting to prevent Passive Arming.

4-1 Aux 1 output – This output must be set through a POC

Through the remote, this option can be programmed for the default setting of a 0.5 second pulsed output. Setting 2

changes the output to a latched setting. The latched output will stay latched until the auxiliary output is activated

again. Setting 3 changes the output of Aux 1 to a 20 second pulse. Setting 4 works in conjunction with the OP500

Option Programmer. With the OP500 you can set Aux 1 to a certain time.

4-2 Aux 2 output – This output must be set through a POC

Through the remote, this option can be programmed for the default setting of a 0.5 second pulsed output. Setting 2

changes the output to a latched setting. The latched output will stay latched until the auxiliary output is activated

again. Setting 3 changes the output of Aux 2 to a 20 second pulse. Setting 4 works in conjunction with the OP500

Option Programmer. With the OP500 you can set Aux 2 to a certain time.

4-3 Aux 1 output Control

1 2 ... 15 16 17 18 19 20 21 22

Keine Kommentare

CompuSTAR CM4200DX Installationsanleitung Seite 20